How to Use Floor Jack On Jeep Wrangler: Simple Guidelines

How to Use Floor Jack On Jeep Wrangler

Having an attractive Hulk-type Jeep Wrangler to drive is quite enjoyable. But a punctured tire on the highway road could be a real hazard. Professional mechanics typically utilize floor jacks to apply powerful forces or lift weights.

But You just need to know “How to Use Floor Jack On Jeep Wrangler. Simply, put your floor jack under the axle tube next to the punctured tire before raising the car and jacking up the Wrangler.

However, down below, you’ll find some effective ideas. Therefore, read the entire article to learn about Jeep lifting with the ideal Jeep Wrangler jack kit.

Why Do You Need A Floor Jack?

A floor jack is usually used for car lifting to relieve the pressure on the tires. It is more adaptable than the other jack.

You’ll get tons of advantages, and one of the most noteworthy benefits of a floor jack is its high raising capacity. The common height capacity of the floor jack is 20 inches. But if you want large capacity, you can find ones with a lifting capability of 30 inches.

Another advantage is that they are made of lightweight material and are easy to move. As a result, most garages will likely use these jacks to lift vehicles quickly.

How To Use A Floor Jack To Lift A Jeep Wrangler

What Type of Jack Should I Use for a Jeep Wrangler?

The capacity of 3 tons would be best for any Jeep Wrangler, where the height they offer is a maximum of 18 inches.

The material of this floor jack is aluminum, and as a result, it helps to reduce weight. Additionally, use a jack stand wherever possible to lift the jack below the car to ensure your safety as well as the safety of your Jeep. For your convenience, we are sharing various types of jacks and their capacity.

Floor Jack Jeep Wrangler Size and Capacity Chart

Not everyone is knowledgeable about the right types of jacks. Therefore, we have made a chart of jack types along with lifting and holding capacity.

Types of JacksHeight Lifting CapacityCapacity of Holding
Hi-Lift jack40 inches4629 to 5291 pounds
Floor Jack3 to 20 inches3000 pounds
Bottle jack5 to 22 inches2000 to 50,000 pounds
Scissor jack15 to 30 inches1000 to 2000 pounds

Where to Put Jack on Jeep Wrangler?

The Jeep Wrangler Jack and Tool Kit Location can be detected by checking the user manual. The manual book says the axle tube is where you should jack up your Jeep Wrangler. Then, the middle part of the differentials shouldn’t be jackknifed. You can also search by “car model and year jack/lift points” to be sure you’re in the right location.

Remember, the Jeep should then be lifted after making sure the jack is correctly engaged. Wrangler’s jack and lug wrench are hidden beneath the cargo area surface and can be found once you complete the task.

How To Use A Floor Jack On Your Jeep

How to Use Floor Jack On Jeep Wrangler: 10 Easy Steps

Here comes the main section of this article. Using a floor jack on your jeep wrangler requires an easy step-by-step process what’s included below.

Check the Owner’s Manual

  • First, take a look at the user manual illustrations that demonstrate how to use the automobile jack tool.
  • Since every Jeep is unique and you have a Jeep Wrangler, you should generally have the ideal type of jack that can lift without hassle.
  • However, following the directions in the manual, verify the jack’s capacity and assure the safety section.
  • Additionally, you can just go through Google to read the Jeep Wrangler Owners Manual PDF.

Prepare All The Tools

Secondly, what we have to do is gather all the tools necessary to lift the heavy Jeep up to our requirements. We crucially require –

  • The ideal floor jack for the Jeep Wrangler
  • Jack stands
  • Include a base plate in addition.

Select The Secured Parking Area

  • First of all, turn off the ignition switch and turn on the hazard lights.
  • When you need to park the Jeep, move it to a flat ground surface or a garage.
  • Choosing to pave floors is advisable because Jacks tend to slip on floors with dirt or grass.
  • You might also need to use any suitable-sized stone to block the left front tire.

Scissor Jack Changing

  • Take off your trunk’s floorboard’s plastic or carpet covering.
  • After that, lace the lug wrench, extension, jack, and jack handle in a comfortable area.

Select the Ideal Floor Jack

  • Having the weight of the Jeep is more than 3500 pounds suggests you need a jack with the capability to lift over 4000 pounds.
  • In general, floor jacks have the capability to hold around 1000–7000 pounds.

Find the Lifting Location

  • Decide where to locate the Jeep.
  • For safety, try to use a Jeep car lift.
  • Next, put it under the center of the Jeep.
  • Make sure it’s between the two wheels of the Jeep Wrangler.
  • After that, set the floor jacks’ height to match the center differential in the back.

 Push The Handle

  • Before starting, confirm that the jack is in the right place.
  • Now move the handle up and down until it raises the Jeep.
  • Then, the floor jack should come out.

Floor Jack Removal Time

  • This time, insert the jack stick, press to raise it, and if required, remove the stands from the axle tubs.
  • The automobile load has now reached the floor jack.
  • After that, the stick should be taken out of the floor jack and attached to the jackscrew, then rotate clockwise.
  • The jeep will come down gradually.
  • Finally, remove the floor jack from the center rear differential last.

Chock wheels

  • Set the chocks around the Jeep tire.
  • As it stops the tires from moving, the tire should be in the middle of the wheel chocks.
  • Try to use wheel chocks in pairs at all times.

Loosen Jeep’s Lug Nuts

  • To remove the lug nuts, use a tire iron. Try not to entirely loosen them up so that they can be rotated by hand.
  • If it’s hard to remove, then you can use liquid thread.
  • Use a wrench to remove the nuts.
  • Lastly, remove the flat tire gently, and it’s suggested to wear gloves.

Take The Spare Tire

  • The spare tire should be in good condition.
  • Ensure that the spare tire is fitted properly; do not head back.
  • Use the lug wrench to tighten the nuts.
  • Put your old tire in the back of the Jeep.

Attach Your Jack Stands

  • Set the jack stand under the lifting point of your Jeep.
  • If needed, adjust the jack stand, but you have to check whether it’s supporting your Jeep or not.
  • Push your car slightly to see if it’s secure.
  • Now you can start your work under the Jeep.

Maintain Weight On Jack Stand

  • Rotate the floor jack screw in the opposite direction.
  • The vehicle will start to come down over the jack stands.
  • Now remove the old tires and add the new ones.

Tighten The Lug Nuts Twice

  • The more the lug nuts are tightened, the more secure you are.
  • To lower the vehicle, turn the jack counterclockwise.
  • Once the vehicle has hit the ground, let the jack out and completely tighten the lug nuts.
  • Rotate lug nuts until each one is tightened at least two times.
  • To make sure they have been tightened appropriately, use a torque wrench.


So, we hope there is nothing left to know about how to use floor jack on jeep wrangler since we have discovered a step-by-step process for lifting heavy Jeeps with a floor jack for any accidental scenario.

While using the floor jack, you must take all the safety measurements. Be careful while handling the weight and tools which may cause any unwanted harm.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *